Posted on

ARIN Reaches IPv4 Depletion | Team ARIN

ARIN is the American Registry for Internet Numbers, the organisation that hands out the blocks IP addresses.

Each region has its own, for instance Australia/Pacific has APNIC. Naturally, they work very closely together.

Open Query can assist you with planning and deployment of IPv6 capabilities on your front-end servers, as well as at the back-end if you wish. Not all hosting providers support IPv6, but many good ones do. MySQL/MariaDB can operate in a native IPv6 or dual stack environment. Open Query enabled its own front-end servers for IPv6 a number of years ago already.

ARIN’s IPv4 free pool has depleted. This is an important milestone for the Internet as now we now usher in the age of IPv6.


ARIN has reached depletion of the general IPv4 free pool today, 24 September 2015. We’ve been talking about the inevitability of IPv4 depletion for many years and have been educating the community about the need to get IPv6 resources and prepare public facing services for the IPv6 Internet, and now is the time to make sure you are taking steps toward preparing for IPv6 as soon as possible.

Posted on

6to4: Easing the IPv6 transition

With the exhaustion of IPv4 address space looming sometime in 2012; probably earlier rather than later, it makes sense to ease on into IPv6 land.  Without straying into tunnel broking and endpoint shenanigans 6to4 is a method of wrapping up IPv6 inside of IPv4.

6to4 performs three functions:

  1. Allocates an IPv6 address block to any host/network that has a global IPv4 address.
  2. Wraps up IPv6 packets inside IPv4 packets for transmission over IPv4 using 6in4 (traffic is sent over IPv4 inside IPv4 packets whose IP headers have the IP protocol number  set to 41; IPv6-in-IPv4. ) 6to4 makes use of IP protocol 41 too, but instead of static endpoints, the endpoint IPv4 address is sourced from IPv6 addresses within the IPv6 packet header.
  3. Routes traffic between 6to4 and “native” IPv6 networks.

As such its pretty easy to implement, especially on our good friend Debian (and its better looking cousin Ubuntu).

I am going to step through setting up a Debian host at Linode.

Step 1 Check your Kernel

Now, the first caveat is that you must be running a 2.6.20+ kernel (At the time of writing the latest linode kernel for Debian was : 2.6 Paravirt (2.6.34-x86_64-linode)). The default ‘Etch’ release kernel (2.6.18) supports IPv6 but woefully implements IPv6 stateful connection tracking, which is just not good enough for a decent firewall. If you have a look under your Linode Configuration Profile you can see what Kernel you are running, and change it to one that is supported; obviously a reboot would be in order if you change it. The linode kernels have IPV6 support compiled in.

But here is the quick way to check whether IPV6 is compiled in, if the following fails IPv6 is either not compiled in or the module has not been loaded:

 $ cat /proc/net/if_inet6
00000000000000000000000000000001 01 80 10 80       lo
fe80000000000000fcfd4afffecff19f 02 40 20 80     eth0


Modprobe is kind of janky and will stop your interfaces coming up if you follow this guide to the letter. You will need to do this first:

As root/sudo divert the old modprobe, this means that any subsequent upgrade won’t blow away your script

dpkg-divert --add --rename --divert /sbin/modprobe.real /sbin/modprobe

Create a replacement /sbin/modprobe script:

/sbin/modprobe.real "$@"

if [ "$1" == "-Q" ] ; then
        exit 0

exit $ret

Step 2 Calculate your new IPv6 address

Any IPv6 address that begins with the 2002::/16 prefix is known as a 6to4 address, as opposed to a native IPv6 address which does not use that prefix. The Internet Assigned Numbers Authority (IANA: has set aside this address space just for 6to4. IPv6 addresses are assigned based upon your IPv4 address; for instance, would become 2002:4acf:fe10::/48

We need some tools to help us calculate our IPV6 address, luckily there is a package for this

$ sudo apt-get install ipv6calc

Now its a matter of plugging in your IPv4 address into ipv6calc to determine your reserved IPv6 address range.

$ ipv6calc -q --action conv6to4 --in ipv4 --out ipv6

and voila your IPv6 address range appears:

2002:4acf:fe10:: (/48)

You get given an address range with a prefix length of 48 bits, which leaves room for a 16-bit subnet field and a 64 bit host address within the subnet.

Step 3 Update your interface configuration

You now need to edit your network configuration file /etc/network/interfaces file

auto tun6to4
iface tun6to4 inet6 v4tunnel
address 2002:4acf:fe10::1
netmask 16
gateway ::
endpoint any
local #fits address
auto tun6to4 # make sure this interface comes up on boot
 iface tun6to4 inet6 v4tunnel
 address 2002:4acf:fe10::1 #first host in this address range
 netmask 16
 gateway :: #special anycast address for 6to4 (2002:c058:6301::)
 endpoint any
 mtu 1472 #The MTU is therefore the normal Ethernet MTU (1500) minus the headers used on the tunnel.
 ttl 255

Restart your interfaces (not recommended):

$sudo /etc/init.d/networking restart

If you want to be a little  but more careful and not wipe out all networking  if something goes wrong (eg you are using Ubuntu or IPv6 is not available), you could just bring up the new interface:

        $sudo ifup tun6to4

Step 4 Update IPv6 Firewall script/rules

Now it’s fairly important (read as critical) to firewall IPv6 stuff as it is with IPv4. Here is a small sample of a firewall that will at the very least not leave you hanging in the breeze. Needless to say you can add your own rules and make this as complex as you need.

# Initialize all the chains by removing all the rules
iptables --flush
iptables -t nat --flush
iptables -t mangle --flush
ip6tables --flush
ip6tables -t mangle --flush
# The loopback interface should accept all traffic
iptables -A INPUT  -i lo -j ACCEPT
iptables -A OUTPUT -o lo -j ACCEPT
ip6tables -A INPUT -i lo -j ACCEPT
ip6tables -A OUTPUT -o lo -j ACCEPT
#Allow IPV6 packets to come over the tunnel
iptables -A INPUT -p ipv6 -i eth0 -j ACCEPT
iptables -A OUTPUT -p ipv6 -o eth0 -j ACCEPT
# Allow outbound DNS queries from the FW and the replies too
iptables -A OUTPUT -p udp -o eth0 --dport 53 --sport 1024:65535 -j ACCEPT
iptables -A INPUT -p udp -i eth0 --sport 53 --dport 1024:65535  -j ACCEPT
ip6tables -A OUTPUT -p udp -o tun6to4 --dport 53 --sport 1024:65535 -j ACCEPT
ip6tables -A INPUT -p udp -i tun6to4 --sport 53 --dport 1024:65535  -j ACCEPT
# Accept and reply to ICMP ping
iptables -A OUTPUT -p icmp --icmp-type echo-request -j ACCEPT
iptables -A OUTPUT -p icmp --icmp-type echo-reply -j ACCEPT
iptables -A INPUT -p icmp --icmp-type echo-request -j ACCEPT
iptables -A INPUT -p icmp --icmp-type echo-reply -j ACCEPT
# IMPORTANT!!!! Allow all icmpv6 because they make IPV6 work
ip6tables -A OUTPUT -p icmpv6 -j ACCEPT
ip6tables -A INPUT -p icmpv6 -j ACCEPT
# Allow previously established connections
iptables -A OUTPUT -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT
ip6tables -A OUTPUT -o tun6to4 -m state --state ESTABLISHED,RELATED -j ACCEPT
# Allow port 80 (www) and 51515 (SSH) connections to the firewall
iptables -A INPUT -p tcp -i eth0 --dport 51515 --sport 1024:65535 -m state --state NEW -j ACCEPT
iptables -A INPUT -p tcp -i eth0 --dport 443 --sport 1024:65535 -m state --state NEW -j ACCEPT
iptables -A INPUT -p tcp -i eth0 --dport 80 --sport 1024:65535 -m state --state NEW -j ACCEPT
ip6tables -A INPUT -p tcp -i tun6to4 --dport 51515 --sport 1024:65535 -m state --state NEW -j ACCEPT
ip6tables -A INPUT -p tcp -i tun6to4 --dport 443 --sport 1024:65535 -m state --state NEW -j ACCEPT
ip6tables -A INPUT -p tcp -i tun6to4 --dport 80 --sport 1024:65535 -m state --state NEW -j ACCEPT
# Allow port 80 (www) and 443 (https) connections from the firewall
iptables -A OUTPUT -j ACCEPT -m state --state NEW,ESTABLISHED,RELATED -o eth0 -p tcp -m multiport --dport 51515,80,443 -m multiport --sport 1024:65535
ip6tables -A OUTPUT -j ACCEPT -m state --state NEW,ESTABLISHED,RELATED -o tun6to4 -p tcp -m multiport --dport 51515,80,443 -m multiport  --sport 1024:65535
# Allow previously established connections
iptables -A INPUT -j ACCEPT -m state --state ESTABLISHED,RELATED -i eth0 -p tcp
ip6tables -A INPUT -j ACCEPT -m state --state ESTABLISHED,RELATED -i tun6to4 -p tcp
# The policy should be to drop it
iptables -A INPUT -j DROP
iptables -A OUTPUT -j DROP
iptables -A FORWARD -j DROP
ip6tables -A INPUT -j DROP
ip6tables -A OUTPUT -j DROP
ip6tables -A FORWARD -j DROP

I usually create a directory called /etc/iptables  (owner root:root  / permissions 750) and drop  firewall up and down scripts in there.

Then it is  a simple matter of adding the following scripts to the bottom of your eth0 interface definition stanza in /etc/network/interfaces to invoke them on boot or whenever:

pre-up /etc/iptables/
post-down /etc/iptables/
pre-up /etc/iptables/
post-down /etc/iptables/

IMPORTANT: Just a quick note don’t block icmpv6 because it is the glue that holds IPv6 together.

Step 5 Setup Forward DNS

I am not going to over explain this one because everyone has an opinion on how to setup DNS but in essence you need to add a line like this to your zone file. There are plenty of articles outlining this stuff.

hyosine			AAAA	2002:4acf:fe10::1

Step 6 Setup Reverse DNS

You now need to setup  reverse DNS for your address, so using our example of 2002:4acf:fe10 you will have to configure the zone of “” in your name servers.  The zone should have PTR records for your hosts just like an zone for IPv4, but with hex digits of the IPv6 address backwards, separated by dots. Using our example, the 6to4 host will have a ::1 suffix, so a reverse DNS record looks like: PTR

You will need to register this zone and its servers with the 6to4 reverse zone authority. eg

Step 7  Test

The ping6 utility is probably best to test whether your host is now working. It’s probably best to try the IPv6 address first:

$ ping6 2002:4acf:fe10::1 
 PING 2002:4acf:fe10::1(2002:4acf:fe10::1) 56 data bytes 
 64 bytes from 2002:4acf:fe10::1: icmp_seq=1 ttl=60 time=1.59 ms 
 64 bytes from 2002:4acf:fe10::1: icmp_seq=2 ttl=60 time=1.42 ms PTR
With that record inside the above zone, the full record would be

Now you can try with the DNS name you just setup. PTR
$ ping6
PING 56 data bytes
64 bytes from 2002:4acf:fe10::1: icmp_seq=1 ttl=60 time=1.41 ms
64 bytes from 2002:4acf:fe10::1: icmp_seq=2 ttl=60 time=1.34 ms

$ ping6

PING 56 data bytes

64 bytes from 2002:4acf:fe10::1: icmp_seq=1 ttl=60 time=1.41 ms

64 bytes from 2002:4acf:fe10::1: icmp_seq=2 ttl=60 time=1.34 ms

Lastly, you need to register this zone and its servers with the 6to4 reverse zone authority. Note that when you visit that site, you’ll get an SSL certificate warning. This is normal. You need to visit this site using IPv6 from the actual 6to4 zone you’re trying to register. Follow the form to set up the nameservers for the zone and that’s it!